Tripp Lite SRWF5U36 Vertical Wall Mount Rack Enclosure Review
When you buy through the Amazon links on this page, we may earn a commission at no extra cost to you. Learn more
Last updated October 31, 2026
The Tripp Lite SRWF5U36 is a good fit if you need to hang a short network run on a wall where floor space is scarce: a patch panel plus a switch, or a UPS and a couple of shallow devices, in a fully assembled, locking, vented steel box with a 5-year warranty. It is a poor fit for deep, front-to-back-ventilated servers or gear you will pull in and out often, because the vertical layout makes servicing awkward.
You get 5U of 19-inch rail space plus a separate 2U patch-panel bracket in a cabinet that stands under 10 inches off the wall.
Where the SRWF5U36 Earns Its Place on Your Wall
The design turns a normal rack on its side. Equipment rotates 90 degrees and faces the ceiling, so the rail height runs front to back. That is how gear up to 36 inches deep fits in a box only 9.7 inches deep.
5U of rails plus a 2U patch bracket
The main rail space holds 5U of 19-inch equipment, and a separate slide-out bracket at the top takes patch panels up to 2.5 inches deep. One box covers the whole run: patch panel on top, switch and UPS below.
Ready to hang
The enclosure ships fully assembled, so there is no build step before it goes on the wall. The front door is locking and reversible, the top panel locks too, and keys come in the box. The door latch also takes a user-supplied padlock. The front door and bottom panels are vented.
Rails and load
The rails are reversible, with M6 threads on one face and 12-24 on the other, and they adjust in 1-inch steps from 33 to 36 inches of mounting depth. Hardware for both thread types is included. The static load rating is 150 lb, and that figure includes the weight of the enclosure itself.
Compliance and warranty
The enclosure meets EIA-310-E and PCI DSS physical-security requirements. The warranty runs 5 years, with spare parts available for 5 years. The assembled build, the locking front door and top panel, and that warranty are what justify the cost over a bare open frame.
Where the SRWF5U36 falls short
The vertical layout has trade-offs that the spec sheet does not spell out, and they matter more than most of the numbers.
Servicing order
In a vertical enclosure, the devices in front have to come out before the one nearest the wall.
Heat rises
A vertically mounted device intakes at the bottom and exhausts at the top. Side-exhaust switches and line-interactive UPSes are fine. Front-to-back servers are the problem case, and this is the most under-reported point about this class of enclosure.
No fans and no fan mounts
The vents are passive, so airflow is something you have to think about yourself.
Wall fasteners are not included
The box ships with rack screws, cup washers and keys, but the M10 or 3/8-inch bolts and fender washers for the wall are user-supplied.
Weight and lifting
The unit weighs 66.1 lb, heavy enough to need a two-person lift. The 150 lb rating includes the enclosure, so the wall has to carry the total.
Other points to check
The model is not listed as TAA compliant, so government buyers should check before bidding.
The product in this review
Tripp Lite SRWF5U36
See on AmazonWhat the SRWF5U36's Rack Units, Depth and Load Rating Mean for Your Gear
These are the figures to check against your gear before you commit.
| Specification | Figure |
|---|---|
| Rack size | 5U of 19-inch equipment, plus 2U patch-panel space |
| Dimensions | 43.2 inches high, 25.6 inches wide, 9.7 inches deep |
| Mounting depth | Adjustable from 33 to 36 inches |
| Unit weight | 66.1 lb |
| Load capacity | 150 lb static, including the unit |
| Rails | Reversible, M6 on one face, 12-24 on the other |
| Doors | Locking, reversible front door; locking top panel; padlock hasp |
| Ventilation | Vented front door and bottom panels, no fans |
| Compliance | EIA-310-E, PCI DSS physical security |
| Warranty | 5-year limited |
| In the box | Enclosure, 12 M6 screws, 12 M6 cup washers, 12 12-24 screws, 2 keys, owner's manual |
Doing the fit math
One rack unit is 1.75 inches, so 5U gives you 8.75 inches of usable rail height. The 2U patch bracket sits on top of that. Measure your deepest device against the 33 to 36 inch rail range, and set the depth before the enclosure goes up.
Mounting points
The back has multiple keyhole slots on 16-inch centers. Use M10 or 3/8-inch bolts, at least four of them, with fender washers. The fasteners are not included.
Hanging the SRWF5U36 and Loading Its Five Units
Most problems with this enclosure come from the wall, not the box. Work through these steps in order.
- Set the rail depth to your deepest device, anywhere from 33 to 36 inches, before the enclosure goes up.
- Mount the empty enclosure with at least four M10 or 3/8-inch fasteners and fender washers.
The Tripp Lite SRWF5U36 is a well-built, fully assembled, locking vertical enclosure that solves the wall-space problem for a short network run, as long as you accept the servicing order and the heat-rises caveat and plan the wall mounting properly. Do the fit math against the 8.75 inches of rail height and the 33 to 36 inch depth range, then work through the installation checklist before you buy.
Frequently asked questions
Depth, rail height and wall strength decide whether this enclosure works in your space, and each one is easy to check before you order.
How much patch panel space does the Tripp Lite SRWF5U36 add on top of its 5U of rails?
A slide-out bracket at the top of the Tripp Lite SRWF5U36 holds up to 2U of patch panels as deep as 2.5 inches, separate from the 5U of 19-inch rails below.
What mounting depth range does the Tripp Lite SRWF5U36 support for deep gear?
The rails adjust in 1-inch steps between 33 and 36 inches of mounting depth, and setting that depth before hanging the cabinet keeps deep equipment from fouling. Because gear faces the ceiling in this vertical layout, equipment up to 36 inches deep fits inside a cabinet only 9.7 inches deep.
Does the 150 lb capacity of the Tripp Lite SRWF5U36 include the cabinet's own weight?
The 150 lb static rating includes the 66.1 lb enclosure, so the wall must carry the combined weight and the usable equipment load is smaller than 150 lb.
What servicing drawback comes with the vertical layout of the Tripp Lite SRWF5U36?
Because the gear faces the ceiling and the rail height runs front to back, the devices in front have to come out before you can reach the one nearest the wall, so servicing is awkward.
Are wall bolts or cooling fans included with the Tripp Lite SRWF5U36?
The Tripp Lite SRWF5U36 relies on passive vents in the front door and bottom panels, with no fans or fan mounts. The M10 or 3/8-inch wall bolts and fender washers are not supplied, so plan on at least four fasteners.