RackSolutions 1URACK-119 Vertical Wall Mount Rack Bracket Review
When you buy through the Amazon links on this page, we may earn a commission at no extra cost to you. Learn more
Last updated October 31, 2026
The RackSolutions 1URACK-119 is a good buy if you need to hang one piece of 19-inch network gear (a switch, router, patch panel, KVM switch or power strip) on a wall or under a desk and you have no floor or rack space to spare. It is the wrong pick for several devices or for a full-depth server without rails.
Home labs, home and small offices, network closets and AV or retail installs are where it fits. The 13-gauge cold-rolled steel, the square-hole EIA mounting pattern, the mounting hardware in the box and the Texas manufacture are what you pay for over a bare bracket.
What the 1URACK-119 is
The 1URACK-119 is a 1U, 19-inch vertical wall-mount rack bracket cut from high-quality 13-gauge cold-rolled steel and made in Texas. It holds one standard 19-inch device and mounts it vertically and flush to a wall, or horizontally under a desk. Two brackets can be installed in pairs for side-by-side horizontal setups.
RackSolutions builds it for small or home offices and for rooms where a full-size rack will not fit. The square holes take standard 19-inch server, networking and telecom equipment, and the sheet lists gear from Dell, HP, IBM, Apple, Sun, Intel, Cisco, Juniper, 3Com and more. Servers, network switches, routers, patch panels, KVM switches and power strips are all named as supported equipment.
Think of it as a space-saving stand-in for a floor or wall cabinet when you have a single device to hang and no room for a box around it.
Why this bracket suits shallow network gear and small spaces
Space saving is the whole point. A vertical flush mount puts the device against the wall and frees the floor and any rack space you were saving, and the under-desk horizontal option gets gear out of sight without a cabinet.
Substantial steel. 13-gauge cold-rolled steel is a lot of metal for a bracket that carries one device, and the black finish is the usual powder coat on this kind of hardware.
Standard mounting. The square-hole EIA pattern takes ordinary rack gear, so the ears on a switch, router or patch panel line up without adapters. The sheet lists the major server and network brands as compatible.
Complete hardware. The box includes the rack bracket. You are not hunting for cage nuts the night the switch arrives.
Flexibility. One bracket covers a wall or a desk, and a pair covers a side-by-side horizontal layout.
US-made. It is manufactured in Texas, which matters to buyers who track origin for their own reasons.
The product in this review
RackSolutions 1URACK-119
See on AmazonWhere the 1URACK-119 runs out of room
One U only. The bracket holds a single 1U device, or a few small non-rack items if you improvise. It is not a multi-device rack. With three or four devices to mount, a small open-frame wall rack is the better shape of product.
Servers need support. The sheet lists servers as supported, but a full-depth server needs rails or L-brackets. The bracket is a mounting point, not a load-bearing shelf, and the ears alone are not meant to carry a server's weight.
Weight depends on the wall. The 200 lb capacity applies to mounting on wooden studs spaced 16 inches on center. On drywall with the included anchors the practical capacity is far lower, because the wall gives out before the steel does.
No enclosure. It is an open bracket: no door, no cable management, no dust protection. Equipment and cabling stay visible and exposed.
Depth. The bracket measures 2.75 inches high and 23.25 inches deep, so the bracket and the equipment it holds protrude into the room. Plan clearance around whatever you hang.
Wall clearance, rail height and load limit on the 1URACK-119 checked against your own gear
| Size | 1U |
|---|---|
| Rack size | 19 inches |
| Material | High-quality 13-gauge cold-rolled steel |
| Mounting | Wall mount; vertical flush to the wall or horizontal under a desk; pairs for side-by-side horizontal setups |
| Dimensions | 2.75 inches high, 23.25 inches deep |
| Weight capacity | 200 lb when mounted on wooden studs spaced 16 inches on center |
| Compatibility | Standard 19-inch server, networking and telecom equipment from Dell, HP, IBM, Apple, Sun, Intel, Cisco, Juniper, 3Com and more; servers, switches, routers, patch panels, KVM switches, power strips |
| Included | Rack bracket, plus mounting hardware |
| Origin | Made in Texas |
| Identifiers | MPN 1URACK-119; UPC 807648001426 |
The product card shows the current price.
The weight question, 200 lb on studs and less on drywall
The 200 lb figure is the bracket's stated capacity when it is mounted on wooden studs spaced 16 inches on center. That is the number to plan around if you are screwing into framing, and it is far more than any switch, router or patch panel will ever weigh.
On drywall with the included anchors, capacity drops well below that. The steel is not the weak point in a drywall install; the wall is. A bracket rated for 200 lb on studs can still pull out of a hollow wall under a load the steel would happily carry.
Hitting studs where you can
The bracket's mounting holes are spaced for 16-inch on-center studs, the standard spacing in US wood-frame walls. Find two studs with a stud finder, mark them, and drive the anchor screws into the framing. That is the install the 200 lb rating describes.
When drywall is the only option
If no stud lines up, the included drywall anchors will hold light gear: a switch, a router or a patch panel is fine. A heavy server is not.
Servers and their ears
Network gear hangs safely from its rack ears at these weights. A server does not: its ears are for locating it in a rack, not for carrying it. Use rails or L-brackets so the chassis weight is supported from below, and treat the bracket as the frame those rails bolt to.
What mounting the 1URACK-119 involves once the box arrives
Vertical on a wall. The bracket sits flush against the wall and the device mounts vertically, so its ports face sideways. This is the tightest use of space and the one that suits closets and narrow walls.
Horizontal under a desk. Mount the bracket horizontally and the device sits as it would in a normal rack. For side-by-side horizontal setups, install brackets in pairs, which the sheet supports.
Studs first. Plan around 16-inch stud spacing. Use the included anchors only for light loads, and check for studs behind the drywall before you commit to a spot.
Hardware check. The kit includes a rack bracket.
Cabling. In the vertical orientation the ports face sideways.
The RackSolutions 1URACK-119 is a well-made, space-saving 1U bracket that earns its place when you have one piece of network gear to hang on a wall or under a desk. It is the wrong tool for a multi-device setup or a full-depth server without rails.
Weigh the steel gauge, the complete hardware kit and the US manufacture against the stud-versus-drywall reality: 200 lb on 16-inch studs, much less on anchors. The product card shows the current price.
Frequently asked questions
Most of the doubt around this bracket comes down to the wall behind it, not the steel in front of it.
How much clearance does the RackSolutions 1URACK-119 need for the gear it holds?
The RackSolutions 1URACK-119 measures 23.25 inches deep and 2.75 inches high, and it sits flush against the wall, so the bracket and the gear you hang protrude into the room; we do not have a separate clearance figure for the gear, so plan clearance around whatever you hang.
Can the RackSolutions 1URACK-119 carry a full-depth server on its ears alone?
No. Network switches, routers and patch panels hang safely from their rack ears at the weights this bracket handles, but a server's ears only locate the chassis and are not built to bear its mass. The 200 lb rating covers the bracket itself on 16-inch studs, not a chassis hanging from its front panel, so a server of any real weight has to be carried from below.
How many RackSolutions 1URACK-119 brackets does a side-by-side horizontal setup take?
Two. A single RackSolutions 1URACK-119 holds one 1U device, and installing brackets in pairs allows two units to sit next to each other horizontally, either under a desk or along a wall. Buyers with three or more devices are better served by a small open-frame wall rack.
Does the RackSolutions 1URACK-119 change how the ports face when mounted vertically?
Yes. Hung vertically and flush to a wall, the RackSolutions 1URACK-119 turns the device so its ports point to the side, which is the tightest fit for closets and narrow walls. Mounted horizontally under a desk, the gear sits the way it would inside a standard rack, with ports facing out.
Does the RackSolutions 1URACK-119 keep dust off the equipment or hide the cabling?
No. The RackSolutions 1URACK-119 is an open bracket with no door, no cable management and no dust shielding, so mounted equipment and its wiring stay visible. Buyers who need a closed box should look at a wall cabinet instead.